Pinnacle ProjectMix I/O Betriebsanweisung

User GuideControl Surface with Motorized Faders and 18 x 14 Audio InterfaceEnglish

ProjectMix I/O User Guide953. Line Inputs (LINE INPUTS): Balanced line-level (+4 dBu) 1⁄4" analog inputs. These inputs are wired in parallel w

10The FireWire Audio Interface The ProjectMix I/O audio interface is capable of several different audio configurations, which are all selectable on the

ProjectMix I/O User Guide11The Control PanelNow we will begin working with the ProjectMix I/O Control Panel software that was installed

12Analog and Digital InputsTo the right of the software returns section on the mixer page are the ProjectMix I/O analog and digital inputs. Analog inp

ProjectMix I/O User Guide13You can create two separate headphone mixes by assigning one of the headphone channels to monitor a different source, such

14Digital Port Selection Sub-Window (digital port selection)This section selects the active digital inputs and outputs, as well as the formats for eac

ProjectMix I/O User Guide15The following radio buttons determine the function of the level knob on the ProjectMix I/O control surface:< sw retur

16The Control Surface While the ProjectMix I/O looks and functions much the same as a typical mixing console, it is important to note that it is most

ProjectMix I/O User Guide17How the ProjectMix I/O Control Surface Works with Pro ToolsChannel FadersThe channel faders are used for level control of d

18Solo and Mute Buttons (SOLO / MUTE)When the MUTE and SOLO buttons are enabled, their LEDs light. Soloed channels flash the MUTE button LEDs on all ot

To access the multi-language version of this manual, please refer to the Driver CD, or visit the Support section of www.m-audio.co

ProjectMix I/O User Guide19Set Up Button (SET UP)Press the SET UP button to access utility functions of the ProjectMix I/O like LCD Contrast. The SET

20To exit Scrub mode, do any of the following: • Press STOP or SCRUB on ProjectMix I/O. • Press the spacebar. • Press escape (F8/ESC). • Pre

ProjectMix I/O User Guide21Page 2 and above: Encoders control parameters specific to individual plug-insAux 3 Button (AUX 3): VST Instruments Page

22Meter Button (MTR)This key will activate the ProjectMix I/O channel meters, which show up as horizontal bar meters in the LCD display.Flip Button (F

ProjectMix I/O User Guide23Zoom Button (ZOOM) When the ZOOM button is lit, the keys are used to change the view of the edit screen. The left arrow d

24 The display variants for different modes toggle the same way in all Multi Channel Strip views. The following exemplifies how they toggle in Value

ProjectMix I/O User Guide25Aux 3 Button (AUX 3): Built-In Channel EQ Functions EQ Assignment Modes Press the AUX 3 button to toggle between the EQ

26 Instrument Edit View < The mode display will show "In ." < Dependent on the CHAN INFO button, the LCD changes in the fol

ProjectMix I/O User Guide27 Plug-In Edit View < The mode display shows "P1" to "P8," depending on the number of the selec

28MIDI Button (MIDI): MIDI ModeThe MIDI button activates MIDI mode on the ProjectMix I/O and opens the built-in MIDI application (see the section of t

Table of ContentsIntroduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

ProjectMix I/O User Guide29SONAR ModeTo enter SONAR mode: Hold down the AUX 4 button while powering on the unit. SONAR mode is confirmed on the LCD di

30 When pressing and holding the ALT button: Encoder Knob 1 controls EQ Band 1 On/Off on Channel 1 Encoder Knob 2 controls EQ Band 1 On/Off on Chan

ProjectMix I/O User Guide31Flip Button (FLIP)Press the FLIP button to switch the parameter assignment between the faders and the encoder knobs (i.e.,

32Live 5 ModeTo enter Live mode: Hold down the AUX 5 button while powering on the unit. Live mode is confirmed on the LCD display when the ProjectMix

ProjectMix I/O User Guide33Meter Button (MTR)This button activates the ProjectMix I/O channel meters, which show up as horizontal bar meters in the LC

34Digital Performer ModeTo enter Digital Performer mode: Hold down the PAN button while powering on the unit. Digital Performer mode is confirmed on t

ProjectMix I/O User Guide35Drag and drop your MIDI connections between the ProjectMix I/O and Mackie Control icons, as shown below:Now launch Digital

36AUX 3 Button Encoder Knobs 1 – 8 control selection of Aux Send Output on selected bank channels 1 – 8. Press the up/down (p, q) arrow buttons to t

ProjectMix I/O User Guide37Locate Buttons (t LOCATE u) The LOCATE (t / u) buttons move the transport to the previous or next assigned marker.Set Butt

38Using MIDI ModeThe ProjectMix Control Application allows you to configure the ProjectMix I/O control surface to communicate standard

ProjectMix I/O User Guide3IntroductionCongratulations on your purchase of the M-Audio® ProjectMix I/O FireWire audio interface and control surface. Th

ProjectMix I/O User Guide39Installing and Running the ProjectMix Control ApplicationWindows XP1. Insert the FireWire Series CD-ROM into your compute

40Using ProjectMix ControlDownloading Current SettingsWhen ProjectMix Control first starts, it will check to see that the ProjectMix I/O is connected t

ProjectMix I/O User Guide41Changing MIDI AssignmentsTo change the assignments to a control, simply click on it with your mouse. A small dialog box wil

42You’ll start the control surface firmware updater by clicking OPTIONS in the upper-left corner of the ProjectMix Control window. Then click on Update

ProjectMix I/O User Guide43ContactIf you have any questions, comments or suggestions about this or any M-Audio product, we invite you to contact us by

44WarrantyWarranty TermsM-Audio warrants products to be free from defects in materials and workmanship, under normal use and provided that the product

4Features and Technical Features < Eight low-noise mic/instrument preamps with gain controls, signal and peak LED metering, phantom power and 66d

ProjectMix I/O User Guide5Controls and Connectors OverviewControls and Connectors Overview

6Controls and Connectors Descriptions1. Instrument Input Selector Switch (INST): The INST switch enables the front-panel instrument input (50) and

ProjectMix I/O User Guide718. Scrub Button (SCRUB): The SCRUB button is typically used in conjunction with the jog wheel (19) to scrub selected au

835. Flip Button (FLIP): The FLIP button will switch the control parameters of the channel faders (13) and their associated encoder knobs (8). (Exa